| 1.DSP controller dies |
 Change a new DSP controller power supply (+5v) in the control box
Use the manostat (UPS)
|
|
| 2. The machine doesn't go home. |
Restart the DSP controller
Use a new DSP controller
Recover the data in DSP controller: MENU=>SYSTEM MAINTENACE=>DATA SETUP=>RECOVER DATA
Reinstall the DSP program ZHBUSB: copy from the CD we sent with the machine. |
|
3. Machine moves to the opposite direction |
The cable maybe loose and you can check the cable.
Change the wire port A+ and A- on motor driver: you can find A+ and A-on the driver in the control box.
Change a new red limit switch
Change the cable connected with the limit switch |
|
| 4. Computer dies when downloading file |
Data is inordinate and format the data in DSP controller: MENU=>SYSTEM MAINTENANCE=>DATA SETUP=>FORMAT DATA
Enlarge the EMS memory and CPU
Change a better computer |
|
| 5.Main spindle doesn't rotate |
Voltage is too low and use the manostat (UPS)
Check the cable connected with the main spindle
Change a new transducer
Change a new main spindle
Date out of order after being copied and recover the data: MENU=>SYSTEM MAINTENACE=>DATA SETUP=>RECOVER DATA |
|
| 6. Machine doesn?ˉt work accurately |
Change the motor of every axis or change the motor driver.
Use ground wire
Fasten the linker of the screw ball |
|
| 7. Engraving size is not right |
Change the pulse equivalent according to the type of the machine (screw machine: 320 160 320; gear machine: 127.3 127.3 400: 320,320,320 for XHYZ6090): MENU=>SYSTEM MAINTENACE=>SYSTEM PARAMATERS=>PULSE EQUIVALENT. |
|
| 8. Machine doesn?ˉt work after opened (including the machine don't go home) |
The switch is broken, change a new switch
There is something wrong with the power, check or change the power
Check the cable connected with the switch and pin in one side of the cable |
|
| 9. Machine strikes sideward peg when it is working |
The sensor switch is broken or the sheet copper of the sensor switch is distort, change a new sensor switch or fix the sheet copper
The dimension of the machine in controller is not right, reset the dimension according to the working size (the soft limited in the DSP): MANU=>MANUAL SETUP=>MOTION LIMIT. |
|
| 10. Blade is broken when engraving |
Lower the engraving speed: MANU=>MANUAL SETUP=>MOTION PARAMATERS LOW SPEED/HGIH SPEED.
If the material is too thick, engraves by steps
Change a better quality blade
Collet is in a wrong position and corrects it. |
|
| 11. There are some leftover of the material when the machine is working. |
Rectify the interspace of the screw of every axis in DSP: MENU=>SYSTEM MAINTENACE=>SCREW INTERSPACE
Change the bearing on the screw ball
Fasten the linker of Y axis (for ball screw machine) |
|
| 12. Red sensor switch is ok but can't stop the machine |
Sensor switch is dirty and clean it
Sheet copper is too far away from the red sensor switch, the best distance is 1-2mm
When we operate machine manually, the sensor switch doesn't work |
|
| 13 Add machine in soft ware TYPE3 |
Open the TYPE3, and find the machining=> set up machines =>choose the FAUNC OMD in CNC machines=>ok |
|
| 14 X-axis or y-axis doesn't move |
Usually it is the problem of the stepper motor, driver and cable connected with the x-axis or y- axis, check them and correct |
|
| 15 How to protect the vacuum hold down table |
Don't hollow out the material when engraving |
|
| 16 How to change Chinese version to English (DSP) |
| Open English version ZHBUSB, Download Controller Menu and Download Label. |
|
| 17.How to solve the problem of message over Z + limited in Type3 |
When we use software TYPE3, we need to set up machine. When we set up machines, the initial position and end position of Z-axis are the same and higher than theZ between contours. |
|
| 18. How to change the language of TYPE3 from Chinese to English |
Open the soft ware type3 and press the button F10. It will appear option windows. You can choose English. |
|
| 19. Oil of the vacuum pump used in CNC Router in American Way1325 |
Use engine oil 68 |
|
home
универсальный фрезеровально - гравировальные станки
